Carbon Steel in Pressure Vessels with CO2

[abarriop]

I would appreciate any recommendations for Carbon Steel in gas separator with 7% CO2.
I would like to avoid Stainless Steel.
What Material do you recommend?

[zanlog]

clad Carbon Steel

[duazo2009]

I would appreciate any recommendations for Carbon Steel in gas separator with 7% CO2.
I would like to avoid Stainless Steel.
What Material do you recommend?

,

Abarriop,

Use Carbon Steel - SA-516 Gr. 70N + 3.2 mm SS 316L CLAD + NACE MR0175

I'm sure it is enough..

Cheers..

Duazo2009

[abarriop]

Thank you very much duazo2009.

Nevertheles there was a mistake in my first message, the quantity of CO2 it isn't 7%, the correct value is 0,7%.

I thought that NACE MR 0175 it was only for SH2.

Please, Would you mind to recommend again with the new data?

Cheers.

,

Abarriop,

Use Carbon Steel - SA-516 Gr. 70N + 3.2 mm SS 316L CLAD + NACE MR0175

I'm sure it is enough..

Cheers..

Duazo2009

[mobek]

it's interesting to see some base their design decision or may be their career on recommendations through internet forums.

[inconel]

it's interesting to see some base their design decision or may be their career on recommendations through internet forums.

There is nothing wrong in asking questions and collecting information as much as possible before going for a critical mission.People asking questions due to various reasons.Few people ask questions for fun,few ask questions to expand their current level of knowledge, few ask questions to know any kind of past failure .

This is my opinion.

Enjoy

[inconel]

it's interesting to see some base their design decision or may be their career on recommendations through internet forums.

There is nothing wrong in asking questions and collecting information as much as possible before going for a critical mission.People asking questions due to various reasons.Few people ask questions for fun,few ask questions to expand their current level of knowledge, few ask questions to know any kind of past failure .

This is my opinion.

Enjoy

[inconel]

I would appreciate any recommendations for Carbon Steel in gas separator with 7% CO2.
I would like to avoid Stainless Steel.
What Material do you recommend?

[link Point to another website Only the registered members can access]
Pls see page number 9+1 or 11-1

[abarriop]

Inconel, thank you very much for your words and your valuable information.

I have CO2 partial pressure of 4 psi (0,28 bar) then we can use Carbon Steel according with your information, but as the design life is 25 years we will use a Inox Clad o Inox Lining.

Regards.

[inconel]

I would appreciate any recommendations for Carbon Steel in gas separator with 7% CO2.
I would like to avoid Stainless Steel.
What Material do you recommend?

[link Point to another website Only the registered members can access]
Pls see page number 10

[inconel]

abarriop,

Pls Refer,

ASTM A 264
Standard specification for Stainless Chromium-Nickel Steel-Clad Plate

ASTM A 265
Standard specification for Nickel and Nickel-Base Alloy-Clad Steel Plate


Useful Links

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[inconel]

abarriop,

Pls Refer,

ASTM A 264
Standard specification for Stainless Chromium-Nickel Steel-Clad Plate

ASTM A 265
Standard specification for Nickel and Nickel-Base Alloy-Clad Steel Plate


Useful Links

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]