IEC & ISA Standards for Control Valves

[gasenilahmad]

Dear All,
Please help me to get any or all of below listed codes :

1. IEC 60534-1-2005 : Industrial-process control valves - Part 1: Control valve terminology and general considerations.
2. IEC 60534-2-1:2011 (ISA-75.01.01-2012) : Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions.
3. IEC 60534-2-3:2015 : Industrial-process control valves - Part 2-3: Flow capacity - Test procedures.
4. ISA-75.02.01-2008 : Control Valve Capacity Test Procedures.
5. IEC 60534-2-4:2009 (ISA-75.11.01-2013) : Industrial-process control valves - Part 2-4: Flow capacity - Inherent flow characteristics and rangeability.
6. IEC 60534-7:2010 : Industrial-process control valves - Part 7: Control valve data sheet.
7. IEC 61298-1:2008 : Process measurement and control devices - General methods and procedures for evaluating performance - Part 1: General considerations.
8. IEC 61298-2:2008 : Process measurement and control devices - General methods and procedures for evaluating performance - Part 2: Tests under reference conditions.

Regards,
Ahmed

[amjadmalik75]

I found these following codes but i think its old versions only, could't find the new ones. hope it will help a little until new ones found.

1. IEC 60534-1-2005 : Industrial-process control valves - Part 1: Control valve terminology and general considerations.
2. IEC 60534-2-1:2011 (ISA-75.01.01-2012) : Industrial-process control valves - Part 2-1: Flow capacity - Sizing equations for fluid flow under installed conditions.
3. IEC 60534-2-3:2015 : Industrial-process control valves - Part 2-3: Flow capacity - Test procedures.
5. IEC 60534-2-4:2009 (ISA-75.11.01-2013) : Industrial-process control valves - Part 2-4: Flow capacity - Inherent flow characteristics and rangeability.
6. IEC 60534-7:2010 : Industrial-process control valves - Part 7: Control valve data sheet.

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]

[link Point to another website Only the registered members can access]
Regards

[Marty Thompson]

Ansi isa–75.02.01–2008

[Marty Thompson]

Ansi isa-75.01.01-2012 (60534-2-1 mod)

[Marty Thompson]

Ansi isa-75.11.01-2013

[gasenilahmad]

Thank you amjadmalik75, thank you Marty.
Anyone can share the remaining standards (IEC 60534-1-2005) , (IEC 60534-2-3:2015) , (IEC 60534-7:2010) , (IEC 61298-1:2008 ) & (IEC 61298-2:2008).
Regards,
Ahmed

[Marty Thompson]

BS EN 60534-1-2005 Industrial-process control valves - Part 1 Control valve terminology and general considerations
IEC 60534-1 2005 Industrial-process control valves – Part 1 Control valve terminology and general considerations

[Marty Thompson]

BS EN 60534-7-2010 (2011) Industrial-process control valves - Part 7 Control valve data sheet

[sambun]

Thank Marty !

[achmadrahmawan]

Thanks a lot Marty!

[nutcha]

Thank you very much for sharing

[jituparekh]

Above links are dead. Please re-upload.