full list:
EN 771-1:2011+A1:2015 Specification for masonry units - Part 1: Clay masonry units
EN 771-2:2011+A1:2015 Specification for masonry units - Part 2: Calcium silicate masonry units
EN 771-3:2011+A1:2015 Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)
EN 771-4:2011+A1:2015 Specification for masonry units - Part 4: Autoclaved aerated concrete masonry units
EN 771-5:2011+A1:2015 Specification for masonry units - Part 5: Manufactured stone masonry units
EN 771-6:2011+A1:2015 Specification for masonry units - Part 6: Natural stone masonry units
EN 772-1:2011+A1:2015 Methods of test for masonry units - Part 1: Determination of compressive strength
EN 772-2:1998 Methods of test for masonry units - Part 2: Determination of percentage area of voids in aggregate concrete masonry units (by paper indentation)
EN 772-2:1998/A1:2005 Methods of test for masonry units - Part 2: Determination of percentage area of voids in aggregate concrete masonry units (by paper indentation)
EN 772-3:1998 Methods of test for masonry units - Part 3: Determination of net volume and percentage of voids of clay masonry units by hydrostatic weighing
EN 772-4:1998 Methods of test for masonry units - Part 4: Determination of real and bulk density and of total and open porosity for natural stone masonry units
EN 772-5:2001 Methods of test for masonry units - Part 5: Determination of the active soluble salts content of clay masonry units
EN 772-6:2001 Methods of test for masonry units - Part 6: Determination of bending tensile strength of aggregate concrete masonry units
EN 772-7:1998 Methods of test for masonry units - Part 7: Determination of water absorption of clay masonry damp proof course units by boiling in water
EN 772-9:1998 Methods of test for masonry units - Part 9: Determination of volume and percentage of voids and net volume of clay and calcium silicate masonry units by sand filling
EN 772-9:1998/A1:2005 Methods of test for masonry units - Part 9: Determination of volume and percentage of voids and net volume of clay and calcium silicate masonry units by sand filling
EN 772-10:1999 Methods of test for masonry units - Part 10: Determination of moisture content of calcium silicate and autoclaved aerated concrete units
EN 772-11:2011 Methods of test for masonry units - Part 11: Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay
EN 772-13:2000 Methods of test for masonry units - Part 13: Determination of net and gross dry density of masonry units (except for natural stone)
EN 772-14:2001 Methods of test for masonry units - Part 14: Determination of moisture movement of aggregate concrete and manufactured stone masonry units
EN 772-15:2000 Methods of test for masonry units - Part 15: Determination of water vapour permeability of autoclaved aerated concrete masonry units
EN 772-16:2011 Methods of test for masonry units - Part 16: Determination of dimensions
EN 772-18:2011 Methods of test for masonry units - Part 18: Determination of freeze-thaw resistance of calcium silicate masonry units
EN 772-19:2000 Methods of test for masonry units - Part 19: Determination of moisture expansion of large horizontally perforated clay masonry units
EN 772-20:2000 Methods of test for masonry units - Part 20: Determination of flatness of faces of aggregate concrete, manufactured stone and natural stone masonry units
EN 772-20:2000/A1:2005 Methods of test for masonry units - Part 20: Determination of flatness of faces of aggregate concrete, manufactured stone and natural stone masonry units
EN 772-21:2011 Methods of test for masonry units - Part 21: Determination of water absorption of clay and calcium silicate masonry units by cold water absorption
CEN/TS 772-22:2006 Methods of test for masonry units - Part 22: Determination of freeze/thaw resistance of clay masonry units
EN 845-1:2013 Specification for ancillary components for masonry - Part 1: Wall ties, tension straps, hangers and brackets
EN 845-2:2013 Specification for ancillary components for masonry - Part 2: Lintels
EN 845-3:2013 Specification for ancillary components for masonry - Part 3: Bed joint reinforcement of steel meshwork
EN 846-2:2000 Methods of test for ancillary components for masonry - Part 2: Determination of bond strength of prefabricated bed joint reinforcement in mortar joints
EN 846-3:2000 Methods of test for ancillary components for masonry - Part 3: Determination of shear load capacity of welds in prefabricated bed joint reinforcement
EN 846-4:2001 Methods of test for ancillary components for masonry - Part 4: Determination of load capacity and load-deflection characteristics of straps
EN 846-4:2001/A1:2004 Methods of test for ancillary components for masonry - Part 4: Determination of load capacity and load-deflection characteristics of straps
EN 846-5:2012 Methods of test for ancillary components for masonry - Part 5: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (couplet test)
EN 846-6:2012 Methods of test for ancillary components for masonry - Part 6: Determination of tensile and compressive load capacity and load displacement characteristics of wall ties (single end test)
EN 846-7:2012 Methods of test for ancillary components for masonry - Part 7: Determination of shear load capacity and load displacement characteristics of shear ties and slip ties (couplet test for mortar joint connections)
EN 846-8:2000 Methods of test for ancillary components for masonry - Part 8: Determination of load capacity and load-deflection characteristics of joist hangers
EN 846-8:2000/A1:2006 Methods of test for ancillary components for masonry - Part 8: Determination of load capacity and load-deflection characteristics of joist hangers
EN 846-9:2000 Methods of test for ancillary components for masonry - Part 9: Determination of flexural resistance and shear resistance of lintels
EN 846-10:2000 Methods of test for ancillary components for masonry - Part 10: Determination of load capacity and load deflection characteristics of brackets
EN 846-11:2000 Methods of test for ancillary components for masonry - Part 11: Determination of dimensions and bow of lintels
EN 846-13:2001 Methods of test for ancillary components for masonry - Part 13: Determination of resistance to impact, abrasion and corrosion of organic coatings
EN 846-14:2012 Methods of test for ancillary components for masonry - Part 14: Determination of the initial shear strength between the prefabricated part of a composite lintel and the masonry above it
EN 998-1:2010 Specification for mortar for masonry - Part 1: Rendering and plastering mortar
EN 998-2:2010 Specification for mortar for masonry - Part 2: Masonry mortar
EN 1015-1:1998/A1:2006 Methods of test for mortar for masonry - Part 1: Determination of particle size distribution (by sieve analysis)
EN 1015-2:1998/A1:2006 Methods of test for mortar for masonry - Part 2: Bulk sampling of mortars and preparation of test mortars
EN 1015-3:1999 Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table)
EN 1015-3:1999/A1:2004 Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table)
EN 1015-3:1999/A2:2006 Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table)
EN 1015-6:1998 Methods of test for mortar for masonry - Part 6: Determination of bulk density of fresh mortar
EN 1015-6:1998/A1:2006 Methods of test for mortar for masonry - Part 6: Determination of bulk density of fresh mortar
EN 1015-7:1998 Methods of test for mortar for masonry - Part 7: Determination of air content of fresh mortar
EN 1015-9:1999 Methods of test for mortar for masonry - Part 9: Determination of workable life and correction time of fresh mortar
EN 1015-9:1999/A1:2006 Methods of test for mortar for masonry - Part 9: Determination of workable life and correction time of fresh mortar
EN 1015-10:1999 Methods of test for mortar for masonry - Part 10: Determination of dry bulk density of hardened mortar
EN 1015-10:1999/A1:2006 Methods of test for mortar for masonry - Part 10: Determination of dry bulk density of hardened mortar
EN 1015-11:1999 Methods of test for mortar for masonary - Part 11: Determination of flexural and compressive strength of hardened mortar
EN 1015-11:1999/A1:2006 Methods of test for mortar for masonary - Part 11: Determination of flexural and compressive strength of hardened mortar
EN 1015-12:2000 Methods of test of mortar for masonry - Part 12: Determination of adhesive strength of hardened rendering and plastering mortars on substrates
EN 1015-17:2000 Methods of test for mortar for masonry - Part 17: Determination of water-soluble chloride content of fresh mortars
EN 1015-17:2000/A1:2004 Methods or test for mortar for masonry - Part 17: Determination of water-soluble chloride content of fresh mortars
EN 1015-18:2002 Methods of test for mortar for masonry - Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar
EN 1015-19:1998 Methods of test for mortar for masonry - Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars
EN 1015-19:1998/A1:2004 Methods of test for mortar for masonry - Part 19: Determination of water vapour permeability of hardened rendering and plastering mortars
EN 1015-21:2002 Methods of test for mortar for masonry - Part 21: Determination of the compatibility of one-coat rendering mortars with substrates
EN 1052-1:1998 Methods of test for masonry - Part 1: Determination of compressive strength
EN 1052-2:1999 Methods of test for masonry - Part 2: Determination of flexural strength
EN 1052-3:2002 Methods of test for masonry - Part 3: Determination of initial shear strength
EN 1052-3:2002/A1:2007 Methods of test for masonry - Part 3: Determination of initial shear strength
EN 1052-4:2000 Methods of test for masonry - Part 4: Determination of shear strength including damp proof course
EN 1052-5:2005 Methods of test for masonry - Part 5: Determination of bond strength by the bond wrench method
EN 1745:2012 Masonry and masonry products - Methods for determining thermal properties
EN 13914-1:2005 Design, preparation and application of external rendering and internal plastering - External rendering
EN 13914-2:2005 Design, preparation and application of external rendering and internal plastering - Part 2: Design considerations and essential principles for internal plastering
CEN/TR 15123:2005 Design, preparation and application of internal polymer plastering systems
CEN/TR 15124:2005 Design, preparation and application of internal gypsum plastering systems
CEN/TR 15125:2005 Design, preparation and application of internal cement and/or lime plastering systems
CEN/TR 15225:2005 Guidance on Factory Production Control for the CE Marking (Attestation of Conformity 2+) of designed masonry mortars
EN 15824:2009 Specifications for external renders and internal plasters based on organic binders
missing AMD's from 2015:
EN 771-1:2011+A1:2015 Specification for masonry units - Part 1: Clay masonry units
EN 771-2:2011+A1:2015 Specification for masonry units - Part 2: Calcium silicate masonry units
EN 771-3:2011+A1:2015 Specification for masonry units - Part 3: Aggregate concrete masonry units (Dense and lightweight aggregates)
EN 771-4:2011+A1:2015 Specification for masonry units - Part 4: Autoclaved aerated concrete masonry units
EN 771-5:2011+A1:2015 Specification for masonry units - Part 5: Manufactured stone masonry units
EN 771-6:2011+A1:2015 Specification for masonry units - Part 6: Natural stone masonry units
EN 772-1:2011+A1:2015 Methods of test for masonry units - Part 1: Determination of compressive strength
and missing standard:
CEN/TR 15125:2005 Design, preparation and application of internal cement and/or lime plastering systems
[link Point to another website Only the registered members can access]
or
[link Point to another website Only the registered members can access]
Reply With Quote
Bookmarks