Chapter 5_1
Elamin, raised a good question. So how we can check average saturation in sim model fast and quick and compare it let say to saturation of well data or gmodel or play with scal data and see results
For example i have to sets of scal data how that will impact to my Sw and apparently reserves

Firstly i prepare second set of scal with following data
SWOF
0.428595 0 1 1.36
0.440147 0.001664 0.906708 0.902168
0.460815 0.001794 0.755375 0.444337
0.483279 0.00262 0.612257 0.213154
0.509156 0.005004 0.472792 0.095297
0.510767 0.005218 0.464956 0.090764
0.512465 0.005452 0.456795 0.086231
0.514261 0.00571 0.448278 0.081698
0.516167 0.005995 0.43937 0.077165
0.518196 0.006314 0.430029 0.072632
0.520364 0.00667 0.420207 0.068099
0.522692 0.007072 0.409847 0.063566
0.525204 0.007529 0.398881 0.059033
0.527929 0.008051 0.387224 0.0545
0.530908 0.008656 0.374775 0.049967
0.53419 0.009364 0.361406 0.045434
0.53784 0.010205 0.346954 0.040901
0.54195 0.011221 0.331203 0.036368
0.546645 0.012474 0.313867 0.031835
0.552113 0.014063 0.294544 0.027302
0.558646 0.016153 0.272644 0.022769
0.56674 0.019047 0.247251 0.018236
0.577333 0.023375 0.216798 0.013703
0.592556 0.030752 0.178212 0.00917
0.619323 0.047409 0.123698 0.004637
0.792122 0.3 0 0.000104
1 1 0 0
/

SGOF
0 0 1 0
0.036361 0.002542 0.683335 0
0.072721 0.02537 0.463762 0
0.109082 0.068665 0.312376 0
0.145443 0.133083 0.208646 0
0.181803 0.219281 0.138051 0
0.218164 0.327919 0.090368 0
0.254525 0.459651 0.058431 0
0.290885 0.615138 0.037243 0
0.327246 0.795035 0.023339 0
0.363607 1 0 0
/

then
i run 1 model with initial scal and import data as i describe in Chapter 5

as all properties in sim folder are dynamic ( if you delete data in sim model all data will disappeared in Petrel ) i create new Sw_scal1 property




Press Enter then NO
you will get new property


now you can run volumetrics
on process tab double click on volume culculations as shown in pictures below




You will be return to


DO the following
Step 1
Define contact by dragging existing contact

In jeneral properties uncheck poro and Ntg

in Oil prop check sw_scal1

Press apply and run
 
Petrel will calculate reserve table

you can import it to excell an get following

for this filed my saturation oil will make 55%

NOTE!!!!!!!!!!! the reserves in table are at reservoir condition to get to standard meter cubic you need to multiply them to shrinkage factor
So you by this approach you can check you reserves in model, average saturation, and play with scal
i mooved to 4share here is link with all chapters

[link Point to another website Only the registered members can access]