Page 29 of 29 FirstFirst ... 19 27 28 29
Results 337 to 346 of 346
  1. Re: Eclipse step by step

    Thanks


    See More: Eclipse step by step
    Last edited by Al-bayati; 02-20-2017 at 04:43 AM.

    My threads; Al-bayati :


    • # ADS
      Spons Circuit
      Join Date
      Always
      Posts
      Many
       
    • Re: Eclipse step by step

      Amazing piece of work Temr, congrats.
      Let's say we have a single SWOF table :
      -- Sw Krw Kro Pcwo
      0.25 0.0 0.9 4
      0.5 0.2 0.3 0.8
      0.7 0.4 0.1 0.2
      0.8 0.55 0.0 0.1
      1.0 1.0 0.0 0.0 /

      Automatically, on day 0 Eclipse gives So= 1-Swc (which is 0.75 in this case) at each block. Can I change the oil saturation distribution without adding more matrices ( SATNUM & TABDIMS respectively). Still, average oil saturation would be of the same value (0.75).

      My threads; demisatere :


      •    Sponsored Links



        -

      • Exclamation Re: Eclipse step by step

        Hi,

        I had taken up a project in Petrel 2015. I have made every possible input. I have to history match my data. The GOR in the observed data rises constantly whereas, in my simulated data it is going doing. I tried to put an extra fault but it didn't help. What parameters do I need to change to match my GOR rise in simulated data.

        My threads; vatvto :


        • #340

          Re: Eclipse step by step

          If poro sample are different then try to establish trend Swc vs Perm. If this are the same sample then i would use Pc value because the displacement pressure much higher during Swc measurements ( mercury, oil injection) comparing to real perm.

          My threads; filosofs :


          • #341

            Re: Eclipse step by step

            Assuming that you don't have gas cap gas cusping to the well and don't have behind the pipe etc crossflows, check if your near well pressure falls below Psat. if it does and GOR is too low QC PVT.

          •    Spons.


          • Re: Eclipse step by step

            Thanks for the answer. I was wondering if the total number of time steps which is 1000 can be increased. Haven't seen anything like that in the manual though, at least as far as 2010 and 2014 editions are concerned.

            My threads; demisatere :


            • Re: Eclipse step by step

              thank you temr and shakespear and all members for this very interesting thread,
              now I am reservoir engineer, i used to go through books and papers, but i never find easy explanation as yours,
              Temr, I know it's little bit late, but I did n't find the initialization chapter.
              could you please upload it.

            • Re: Eclipse step by step

              can i get this book free i appreciate

              My threads; nabelT :


              • #345

              • #346

                Join Date
                Jan 2009
                Location
                ALA, KZ
                Posts
                435

                Re: Eclipse step by step

                Hello, people.
                Soory for keeping silence was a little bit busy
                I will try to upload threads in other server.
                I will let you know after.
                Also i am very interesting if any had a chance with developing tool for production forecast ( decline cure + matbal)
                I have some ideas and want to strart diff thread if you all will contribute to this idea

              •   

              Similar Threads

              1. Replies: 11
                Last Post: 07-31-2016, 04:02 AM
              2. Aspen Engineering suite 2006 : Installation step-by-step guide
                By monycash in forum Process Simulation Community
                Replies: 22
                Last Post: 12-06-2015, 10:53 AM
              3. Eclipse Step by Step?
                By Zuper in forum Reservoir
                Replies: 2
                Last Post: 04-05-2012, 12:56 AM
              4. Step by step to calculate control valve Cv thorugh Intools
                By hswang2 in forum Instrumentation & Control
                Replies: 1
                Last Post: 11-28-2010, 09:37 AM
              5. Eclipse step by step
                By temr in forum Engineering Software Tutorial
                Replies: 20
                Last Post: 10-12-2009, 05:34 PM

              Tags for this Thread

              Bookmarks

              Posting Permissions

              • You may not post new threads
              • You may not post replies
              • You may not post attachments
              • You may not edit your posts
              •