Now We can access Petroleum Community by domain www.petrolcom.net______________ website new domain www.petrolcom.net
Page 1 of 2 1 2 LastLast
Results 1 to 12 of 18

Thread: Iso 5167

  1. #1

    Join Date
    Feb 2010
    Location
    India
    Posts
    54
    Thanks
    1
    Thanked 0 Times in 0 Posts

    Iso 5167

    Hi Freinds

    Does someone have a copy of ISO 5167 ?

    Shankar Mathur

  2. # ADS
    Spons Circuit advertisement
    Join Date
    Always
    Location
    Advertising world
    Posts
    Many
     
  3. #2

    Join Date
    Apr 2010
    Posts
    1,881
    Thanks
    37
    Thanked 1,205 Times in 593 Posts
    ISO 5167-1 Measurement of fluid flow by means of D.P. Meters - General principles & Requirements.pdf

    [This link Point to another website Only registered and activated users can see links.]
    ISO 5167-2 Orifice plates.pdf

    [This link Point to another website Only registered and activated users can see links.]
    ISO 5167-3 Nozzles and Venturi nozzles.pdf

    [This link Point to another website Only registered and activated users can see links.]
    ISO 5167-4 Venturi Tubes.pdf

    [This link Point to another website Only registered and activated users can see links.]


  4. The Following User Says Thank You to Nabilia For This Useful Post:

    aabdulaslam@gmail.com (12-20-2011)

  5.    Sponsored Links



    -

  6. #3

    Join Date
    Feb 2010
    Location
    India
    Posts
    54
    Thanks
    1
    Thanked 0 Times in 0 Posts
    Many Thanks Nabilia

    Shankar Mathur

  7. #4

    Join Date
    Jan 2011
    Posts
    4
    Thanks
    0
    Thanked 0 Times in 0 Posts
    Can u please advise what is the maximum allowable differential pressure across the orifice plate according to ISO 5167.

  8. #5

    Join Date
    Apr 2010
    Posts
    1,881
    Thanks
    37
    Thanked 1,205 Times in 593 Posts
    From ISO 5167-2
    5.1.2.3 Care shall be taken in the design of the orifice plate and its installation to ensure that plastic buckling and elastic deformation of the plate* due to the magnitude of the differential pressure or of any other stress* do not cause the slope of the straight line defined in 5.1.3.1 to exceed 1 % under working conditions.
    NOTE Further information is given in 8.1.1.3 of ISO/TR 9464:1998.

  9. #6

    Join Date
    Apr 2010
    Posts
    1,881
    Thanks
    37
    Thanked 1,205 Times in 593 Posts
    I found the 9464 for you.

    BS ISO TR 9464-1998 - Guide to the use of ISO 5167-1-1991.pdf 5.676 MB

    [This link Point to another website Only registered and activated users can see links.]


  10. The Following 2 Users Say Thank You to Nabilia For This Useful Post:

    aabdulaslam@gmail.com (12-20-2011), sudharshanan (05-14-2011)

  11. #7

    Join Date
    Feb 2009
    Location
    India
    Posts
    15
    Thanks
    3
    Thanked 0 Times in 0 Posts

    Re: Iso 5167

    dear sir*

    please upload again as its deleted.

  12. #8

    Join Date
    Jan 2011
    Posts
    147
    Thanks
    461
    Thanked 381 Times in 80 Posts

    Re: Iso 5167

    ISO 5167

    [This link Point to another website Only registered and activated users can see links.]


  13. The Following User Says Thank You to aabdulaslam@gmail.com For This Useful Post:

    irfpat (12-06-2012)

  14. #9

    Join Date
    Sep 2011
    Posts
    8
    Thanks
    1
    Thanked 0 Times in 0 Posts

    Re: Iso 5167

    please upload again

  15. #10

    Join Date
    Apr 2011
    Posts
    1
    Thanks
    0
    Thanked 0 Times in 0 Posts

    Re: Iso 5167 complete ctandard and/or a software

    Dear*

    are those links fuctioning at all* and also is there any good and easy to use software to be able to calculate based on all 4 pats of 5167.

  16. #11

    Join Date
    Jul 2010
    Location
    Bangalore, India
    Posts
    108
    Blog Entries
    1
    Thanks
    3
    Thanked 2 Times in 2 Posts

    Re: Iso 5167

    Please upload again.....Link not working

  17. #12

    Join Date
    Jan 2011
    Posts
    147
    Thanks
    461
    Thanked 381 Times in 80 Posts

    Re: Iso 5167

    [This link Point to another website Only registered and activated users can see links.]


  •   

Similar Threads

  1. Iso 5167
    By salmanisn in forum Pipeline And Fluid Flow
    Replies: 9
    Last Post: 04-14-2016, 10:13 AM
  2. ISO 5167 calculation for restriction orifice
    By l_festo in forum Engineering Software Tutorial
    Replies: 4
    Last Post: 02-14-2015, 02:03 PM
  3. Needs for Iso 5167-2:2003
    By saiedmehdipour in forum Instrumentation & Control
    Replies: 5
    Last Post: 01-01-2014, 09:52 AM
  4. ISO 5167 and ISO 12213 (AGA 8* SGERG-88)
    By jtodic in forum Engineering Software Tutorial
    Replies: 0
    Last Post: 05-29-2013, 03:13 PM
  5. Iso-5167
    By Hendra in forum Instrumentation & Control
    Replies: 2
    Last Post: 09-22-2010, 04:04 AM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •